Search found 11 matches

by The only sarge
Tue Sep 06, 2016 10:14 am
Forum: Load Master forum
Topic: Case Feeder 9 x 19 mm
Replies: 9
Views: 1567

Re: Case Feeder 9 x 19 mm

If I have the two screws "tight" mine doesnt push the case in all the way. I have to loosen the bottom one and then it works fine.
by The only sarge
Mon Jan 21, 2013 8:09 am
Forum: Turret presses
Topic: CASE EJECTOR - SWEET!
Replies: 21
Views: 13966

That "ejector" would slow me down. I keep everything running with my left hand. The shell holder stays at 7 O'clock for me. By having to move it to 3 O'clock I would have to use my right hand to install brass (awkward) from the other side. I load brass, bullets and remove the cartridge all...
by The only sarge
Tue Jan 15, 2013 10:53 pm
Forum: Pro 1000 discussion
Topic: .40 case feeding issues on Pro1000
Replies: 0
Views: 1699

.40 case feeding issues on Pro1000

I have run many a 9mm/.45 ACP on the old lee 1000. So I thought Id run a few .40 calibers versus running them on the old turret press. The cases would tip/pop/fall over one after the other. I had the large case feeder/bent Z bar and the small case slider. Just like the book/instructions say to do. J...
by The only sarge
Mon Jan 14, 2013 7:38 am
Forum: Pro 1000 discussion
Topic: Lee Pro 1000 - - Stuck in Up position
Replies: 6
Views: 3253

Trying to understand your original question/statement here.....
Your saying on your Pro1000 you pulled the handle down and the carrier assembly went up. Then you pushed the handle in and the ram came down with the carrier assembly somehow hanging to the underside of the die plate?
by The only sarge
Sun Jan 13, 2013 4:54 pm
Forum: Pro 1000 discussion
Topic: Ok, I give up. What do you do with your primers????
Replies: 5
Views: 3914

I clean my Pro1000's about every 1000 rounds .......so I remove the base anyway and it holds more than a 1000 primers easy. I sorta like the idea to have all of the spent primers in one convenient pile to sweep into the can frankly.
by The only sarge
Sat Jan 12, 2013 7:30 pm
Forum: Pro 1000 discussion
Topic: Surface Rust
Replies: 6
Views: 3778

RemOil and a wire brush make mine shiny and clean.
by The only sarge
Sat Jan 12, 2013 4:45 pm
Forum: Turret presses
Topic: problem/ intermiten
Replies: 14
Views: 5834

When mine does that I clean it with a shot of brake cleaner and it is good to go.
by The only sarge
Sat Jan 12, 2013 4:40 pm
Forum: Turret presses
Topic: Seating + crimping
Replies: 14
Views: 6993

I have for many years and many rounds set my seating die as such..... I put a empty case in the shell holder. I raise the ram all the way up with the empty case. I screw my bullet seating die down until it stops on the top of the empty case. I then take the case out and screw the die in one half tur...
by The only sarge
Thu Jan 10, 2013 5:47 pm
Forum: Turret presses
Topic: LEE CTP video/9mm
Replies: 19
Views: 10103

I load my own cast and quite a bit of plated/jacketed.
Thanks for the info friend.
by The only sarge
Thu Jan 10, 2013 11:21 am
Forum: Turret presses
Topic: LEE CTP video/9mm
Replies: 19
Views: 10103

I went to his website and saw it is about $500 after shipping. No other info.
Couldnt a $30 RCBS bullet feed die accomplish the same thing?
Without all the power gizmo's and such I mean. Just a basic bullet feeder for a turret press.
Thank you for your response.
by The only sarge
Wed Jan 09, 2013 9:31 am
Forum: Turret presses
Topic: LEE CTP video/9mm
Replies: 19
Views: 10103

I am curious of the bullet feed. Is that a RCBS bullet feed die with Home Depot PVC?

Go to advanced search