Search found 70 matches

by tnmedic
Wed Aug 05, 2015 7:17 pm
Forum: All other Lee Equipment discussion
Topic: Auto disk leaking badly
Replies: 5
Views: 2075

Auto disk leaking badly

Last time I reloaded 223 on my loadmaster it wasn't bad, I spilled a little powder but I went to set up my dies the other day after a long hiatus from 223. Using my charge bar I was running empties to get an average of what the powder measure was dropping, last time I used it was right at 24.6 grain...
by tnmedic
Tue Jul 28, 2015 7:17 pm
Forum: Load Master forum
Topic: Inline Fabrication Ceiling Light
Replies: 7
Views: 2065

Well got my light in, very well made, my turrets apparently are very well made as well. I do not have a drill press so I had to get a 3/4 inch drill bit to try and remove the piece of aluminum from the center of the turrets. Only almost broken my wrist twice. Finally got the light to fit in the cent...
by tnmedic
Fri Jul 24, 2015 9:40 pm
Forum: Buy, Sell and Trade
Topic: WTB hand primer
Replies: 1
Views: 1109

WTB hand primer

Just putting this out there. I have looked at several on the web and read a ton of reviews. It didn't matter the brand the reviews were all the same, it's great, it sucks, save your money, blah blah blah. Anyway if anyone has a hand primer they don't like or don't use and want to sell it cheap, let ...
by tnmedic
Fri Jul 24, 2015 9:37 pm
Forum: Load Master forum
Topic: Inline Fabrication Ceiling Light
Replies: 7
Views: 2065

I ordered the ceiling light kit, and it comes with the 4 led strip as well for the back side of the press and the light insert for the turret, they sent me an email this evening saying it shipped by usps so maybe I will get it by next Friday. I used to make printed circuit boards at home using coppe...
by tnmedic
Fri Jul 24, 2015 3:15 pm
Forum: Load Master forum
Topic: Inline Fabrication Ceiling Light
Replies: 7
Views: 2065

Inline Fabrication Ceiling Light

Anybody use the inline fabrication ceiling light kit for the loadmaster? I am really wanting to buy one. I know some have found cheap led flashlights that fit in the center hole like the inline fab kit does but doesn't have the led strip for the back side of the press. Anyway I guess I am about to o...
by tnmedic
Mon Jun 22, 2015 8:35 pm
Forum: Load Master forum
Topic: I am confused.
Replies: 4
Views: 1407

I trim rifle everytime, that is just a part of my prep for me, it was just weird, I think I figured it out, I think I slipped a universal decapping rod in place of the 223 neck sizing pin and there for some case the necks aren't expanded. Anyway I pulled all the cases I couldn't get the trimmer into...
by tnmedic
Sun Jun 21, 2015 10:38 pm
Forum: Load Master forum
Topic: I am confused.
Replies: 4
Views: 1407

I am confused.

I have been prepping about 2800 or so 223 cases the last couple of weeks. Between work, wife, and kids, don't seem to have the time to just sit down and do it all at once. I have gotten all the brass deprimed and full length resized. Been working on trimming and that is where I am confused. Some of ...
by tnmedic
Thu Jun 11, 2015 11:10 pm
Forum: Load Master forum
Topic: Primer pocket crimp removal?
Replies: 31
Views: 6516

think this has ran it's course, it can be locked now
by tnmedic
Tue Jun 09, 2015 10:26 pm
Forum: Load Master forum
Topic: Primer pocket crimp removal?
Replies: 31
Views: 6516

maybe, I am sorry tho, I hate it when I try and buy something from somewhere and they never get back to me
by tnmedic
Tue Jun 09, 2015 1:19 pm
Forum: Load Master forum
Topic: Lee Loadmaster are they junk?
Replies: 34
Views: 8204

No experience with reloading and the loadmasters "instruction manual" is how I ended up here, watching the videos then joining the forums for dedicated loadmaster support, not the typical you should have bought a Dillon and not a "junky" lee.
by tnmedic
Tue Jun 09, 2015 12:27 pm
Forum: Load Master forum
Topic: Primer pocket crimp removal?
Replies: 31
Views: 6516

No I just told her that I wanted to buy the swage set and gave the part number off the website, I am about to order it now and will order the O press Friday from amazon
by tnmedic
Mon Jun 08, 2015 6:35 pm
Forum: Load Master forum
Topic: Primer pocket crimp removal?
Replies: 31
Views: 6516

Hey tcook, I heard back from CH4D this evening, the sales girl sent me an email so she could get me a quote. If you use the contact us page on ch4d's website and email sales, she should get back to you within a few days. Anyway I am getting an O press and this die and being done with it
by tnmedic
Mon Jun 01, 2015 8:17 pm
Forum: Load Master forum
Topic: Primer pocket crimp removal?
Replies: 31
Views: 6516

Mike, will that work in a loadmaster, or does it have to be a single stage press? I only have my loadmaster is why I am asking. Anyway thanks for the advice appreciate it. TN Medic
by tnmedic
Mon Jun 01, 2015 5:15 pm
Forum: Load Master forum
Topic: Primer pocket crimp removal?
Replies: 31
Views: 6516

Primer pocket crimp removal?

I bought some range pickup brass on another forum I frequent and it was good brass but of course it seems most if not all brass it seems most of it is crimped primers. In the past I have use an oversized drill bit and just drilled the crimp out but that gets tiring and fairly messy. I have been look...
by tnmedic
Sun Jan 25, 2015 1:57 pm
Forum: Load Master forum
Topic: Pro Auto Disk Tightening? (move if needed)
Replies: 12
Views: 2658

Win231 I haven't noticed leaking but with AA2230 I get a lot of leaking, it gets kind of messy after a few hundred rounds. Let us know what you come up with, if you don't mind.

Go to advanced search