Search found 8 matches

by CurlyShuffle
Wed Dec 13, 2017 7:33 pm
Forum: Load Master forum
Topic: Primer rocker arm not coming back up
Replies: 3
Views: 27

Re: Primer rocker arm not coming back up

I had some time off this afternoon, so after doing some shooting at a local range, I decided to look into my primer arm issue further. Well, I guess a "worse case scenario" happened. The carrier has cracked near the primer arm. No mistaking it. :cry: :evil: I think I only loaded about 1500...
by CurlyShuffle
Tue Dec 12, 2017 2:40 am
Forum: Load Master forum
Topic: Primer rocker arm not coming back up
Replies: 3
Views: 27

Primer rocker arm not coming back up

Hello All, I was in the middle of loading some 9mm and I noticed that the indexing was binding up. After some initial investigation, I found out that the primer rocker arm isn't springing back up, causing the Loadmaster not to Index. In fact, when I try to manually manipulate it, the rocker arm itse...
by CurlyShuffle
Sun Sep 10, 2017 10:59 pm
Forum: All other Lee Equipment discussion
Topic: Lee Auto Drum disassembly instructions?
Replies: 2
Views: 306

Re: Lee Auto Drum disassembly instructions?

I figured it out! :mrgreen: Once you take off the metering drum, you'll see a retaining ring on the same side as the screw/nut you just removed. I took a small flathead screwdriver to pop off that ring. Once that ring was off, I was able to take the other plastic covers off and the gears came off as...
by CurlyShuffle
Tue Sep 05, 2017 3:52 pm
Forum: All other Lee Equipment discussion
Topic: Lee Auto Drum disassembly instructions?
Replies: 2
Views: 306

Lee Auto Drum disassembly instructions?

Hello,

Is there either written instructions or possibly an instructional video on how to completely disassemble a Lee Auto Drum powder measure for repair? I think I messed up the gears or potentially the range of motion on my Auto Drum being a bit ham-fisted during a reloading session.

Thanks!
by CurlyShuffle
Tue Aug 29, 2017 4:48 pm
Forum: Load Master forum
Topic: Occasionally crushing cases in my new Loadmaster
Replies: 7
Views: 668

Re: Occasionally crushing cases in my new Loadmaster

Websterz, When I did some additional research on the Lyman M dies, I came across a YouTube video from FortuneCookie45LC regarding Lyman dies. He mentioned that there is a separate attachment for the M dies that give it the same powder through ability as the Lee die. You would then use the Lyman powd...
by CurlyShuffle
Tue Aug 29, 2017 2:04 pm
Forum: Load Master forum
Topic: Occasionally crushing cases in my new Loadmaster
Replies: 7
Views: 668

Re: Occasionally crushing cases in my new Loadmaster

What do you use as a powder drop if are using the Lyman M die for flaring?
by CurlyShuffle
Mon Aug 28, 2017 12:59 am
Forum: Load Master forum
Topic: Occasionally crushing cases in my new Loadmaster
Replies: 7
Views: 668

Occasionally crushing cases in my new Loadmaster

Hello, Somewhat recently I got my first LoadMaster (40 S&W). I've been able to load a little over 200 rounds so far (all 180 gr Hornady XTP). Once I've tinkered everything, it seems to run pretty well, with one occasional exception. I've crushed 15 cases. I would guess the obvious solution to th...
by CurlyShuffle
Thu Jul 27, 2017 2:14 am
Forum: Pro 1000 discussion
Topic: Possible timing issue with Lee Pro 1000?
Replies: 1
Views: 408

Possible timing issue with Lee Pro 1000?

Hello, I just got my first progressive press, the Lee Pro 1000 in 9mm. During the setup process, I was seeing how the primers would seat into the cases. I quickly noticed after a few rounds that some primers were coming in sideways, or upside down. It was obviously a little frustrating. :x I went ah...

Go to advanced search