Could not have chosen a worse product name. Get an ambitious DA like the one that went after Zimmerman in a politically charged self defense shooting, and try to defend "R.I.P.".
Stupid, stupid, stupid.
Search found 628 matches
- Sun Apr 13, 2014 9:08 pm
- Forum: Odds and Ends
- Topic: New ammo! This stuff will be AMAZING.
- Replies: 11
- Views: 5234
- Sat Feb 22, 2014 9:04 am
- Forum: Odds and Ends
- Topic: remove crimp
- Replies: 11
- Views: 2543
- Wed Feb 19, 2014 8:32 am
- Forum: Odds and Ends
- Topic: Case trimmer
- Replies: 2
- Views: 1260
- Wed Feb 19, 2014 8:22 am
- Forum: Odds and Ends
- Topic: remove crimp
- Replies: 11
- Views: 2543
- Sat Feb 15, 2014 4:49 pm
- Forum: Load Master forum
- Topic: 40 S&W - The way I do it.
- Replies: 72
- Views: 10992
- Sat Feb 15, 2014 4:43 pm
- Forum: Load Master forum
- Topic: Sloppy Ram
- Replies: 21
- Views: 5532
Little bit of caked up grease, dirt and such was the issue... was worried that the ram or the press was worn from excessive use....lol pulled it apart....wiped it down...greased, new wave washers....tight and smooth now!! :D Good job, glad it worked out. I may not post a lot...but look at my member...
- Sat Jan 25, 2014 10:00 am
- Forum: Odds and Ends
- Topic: Sneaky Pete Holster
- Replies: 27
- Views: 6068
- Sat Jan 25, 2014 9:48 am
- Forum: Odds and Ends
- Topic: It was 6 years ago today
- Replies: 4
- Views: 1830
I joined this forum about 3 weeks after you had shot yourself and remember very vividly your ordeal and your honesty. Back then you didn't know how anything would turn out yet. I have appreciated your periodic updates sharing your recovery. You are still in my prayers over losing Candy and I am happ...
- Mon Nov 25, 2013 12:21 am
- Forum: Load Master forum
- Topic: Thanks for all the support
- Replies: 9
- Views: 2494
- Wed Jul 03, 2013 10:58 pm
- Forum: Load Master forum
- Topic: Primer Shield
- Replies: 16
- Views: 5037
- Sun Jun 16, 2013 6:40 pm
- Forum: Load Master forum
- Topic: hello from NZ!
- Replies: 14
- Views: 4135
- Sun Jun 16, 2013 1:49 am
- Forum: Load Master forum
- Topic: Priming system
- Replies: 25
- Views: 5853
Knock on wood here, but with the last newest greatest version of small and large primer assemblies,... Are you talking about the versions from Lee, or the versions that are modded here in the forum? I am still using the original priming systems, But I am down to only a couple of small primer slider...
- Sat Jun 08, 2013 7:08 pm
- Forum: Load Master forum
- Topic: Only trying to help re:Priming
- Replies: 10
- Views: 3557
- Sat Jun 08, 2013 6:59 pm
- Forum: Load Master forum
- Topic: Loadmaster Coming, Need suggestions for accessories.
- Replies: 15
- Views: 6275
Jumping Frog, you will need some means to trim some pistol or revolver cases if you shoot hot loads as the cases will stretch significantly, eg, hot 44 mag loads will stretch the case up to .008 and will need to be trimmed. So you will need to trim some cases, depends on the caliber. The OP specifi...
- Sun Jun 02, 2013 11:55 pm
- Forum: Bullet casting
- Topic: 2new molds
- Replies: 7
- Views: 4249
Re: 2new molds
... i am wanting a NOE and one RCBS mold. Personally, I am not as pleased with my NOE mold. IMO, Accurate Mold makes better molds than NOE by far. As far a Lyman goes, the old molds are OK, but I'd steer way clear of anything newer than 10 years. Their quality control has slipped a lot and have dev...