Search found 118 matches

by john127
Mon Oct 31, 2016 2:07 pm
Forum: Load Master forum
Topic: Issues with new Lee parts
Replies: 24
Views: 4094

Re: Issues with new Lee parts

Magic Mike: Speaking of the 6s substitute plate, I followed your advice & couldn't be happier with the results. Granted, my bevel modification was not as precise as yours but it seems to work & I no longer have primer problems as I did with the 19s. Sure, I'll get an occasional minor smiley ...
by john127
Fri Oct 28, 2016 4:52 am
Forum: Load Master forum
Topic: LLM
Replies: 7
Views: 1250

Re: LLM

Not a bad deal but 1 headache at a time is enough... :mrgreen:
by john127
Tue Oct 25, 2016 12:33 am
Forum: Load Master forum
Topic: S&B 9mm brass
Replies: 4
Views: 782

Re: S&B 9mm brass

Octopuss.....this stuff seems like good quality brass & the tight pockets would probably hardly be noticed on any other priming system but given that the LLM priming system is so temperamental its probably not a good idea to be using it on this press, unless, that is, you modify the pockets.
by john127
Thu Oct 20, 2016 3:48 pm
Forum: Load Master forum
Topic: S&B 9mm brass
Replies: 4
Views: 782

S&B 9mm brass

I believe I read someone's comment about the use S&B 9mm brass on the LLM on this forum some time ago but cannot locate it with the search function, but wanted to give a heads-up that this brass (at least the ones I have) have very tight primer pockets & probably shouldn't be used on this pr...
by john127
Sun Oct 16, 2016 11:58 pm
Forum: Load Master forum
Topic: Case feeder nightmare
Replies: 13
Views: 2003

Re: Case feeder nightmare

The recommended method of adjusting the tension on the plastic friction part that slides up & down the square bar is to fully tighten (do not over tighten) the uppermost screw & lightly adjust the lower one until you attain the desired tension. In other words, its the lower screw that's the ...
by john127
Tue Sep 27, 2016 9:02 pm
Forum: Load Master forum
Topic: Well , I finally did it
Replies: 7
Views: 1773

Re: Well , I finally did it

Yeah GD, that's a fact. One can use the new Auto Drum either way. Hadn't thought about that one.
by john127
Mon Sep 26, 2016 12:20 pm
Forum: Load Master forum
Topic: Case Feeder 9 x 19 mm
Replies: 9
Views: 1613

Re: Case Feeder 9 x 19 mm

erle wrote: WebsterZ has a very simple spring mod that will take care of taller cases tipping over. He calls it the "tip-stop"....


Does he have a website to view this mod?
by john127
Sat Sep 24, 2016 1:38 am
Forum: Load Master forum
Topic: Well , I finally did it
Replies: 7
Views: 1773

Re: Well , I finally did it

You can eliminate the chain altogether by buying the Lee Powder Drum. It has its own internal spring return.
by john127
Fri Sep 23, 2016 11:43 am
Forum: Load Master forum
Topic: Lee service is top notch
Replies: 13
Views: 2319

Re: Lee service is top notch

Yeah, one way to circumvent the crooked hole problem on the LLM turrets is to bite the bullet & buy the ones from Magic Mike. While they may be more costly, at least you know they'll work & you can eliminate that from your diagnosis.
by john127
Fri Sep 23, 2016 11:34 am
Forum: Load Master forum
Topic: Case Feeder 9 x 19 mm
Replies: 9
Views: 1613

Re: Case Feeder 9 x 19 mm

Yes, like some have already stated, the information I've been seeing for some time now, plus experienced for myself, is that the upper screw should be tightened snugly while the lower one is the friction adjuster. I had similar problems with the case feeder using 9mm cases, especially when there was...
by john127
Wed Aug 03, 2016 3:33 am
Forum: Load Master forum
Topic: Lee service is top notch
Replies: 13
Views: 2319

Re: Lee service is top notch

Maybe they're feeling the competition pinch a little more these days & want to woo more customers.
by john127
Tue Jul 05, 2016 1:34 pm
Forum: Load Master forum
Topic: Is the forum still alive?
Replies: 6
Views: 1299

Re: Is the forum still alive?

I believe it's still alive but needs a little oxygen therapy from time to time to keep itself going. :mrgreen:
by john127
Tue Jun 14, 2016 12:09 pm
Forum: Load Master forum
Topic: Opening up the center "hole" in turret
Replies: 6
Views: 1562

After reading this thread, I tried knocking out the center with a slightly loose fitting socket & hammer & it's true, it knocks right out like on an electrical box.
by john127
Sun Jun 05, 2016 1:30 pm
Forum: Load Master forum
Topic: I've made a change to my case pushers.
Replies: 30
Views: 5300

Thanks for the description websterz. Just wanted to know how yours was an improvement over Lee's & you gave a decent explanation. Makes sense that yours would slide more smoothly.

Will the metal to metal contact cause the carrier & feed rod to wear sooner?
by john127
Sun Jun 05, 2016 1:34 am
Forum: Load Master forum
Topic: What should I update?
Replies: 8
Views: 1699

beretta92_fs2003 wrote:And, the heavy guide pin on all my turret plates, the ram won't even wiggle.


I can't picture this in my head, can you post a picture so I can understand?



+1

Go to advanced search