Mod for powder return chain??

[Mike-Mat]

These are actually pretty cheap. It even comes with a spring.

http://cgi.ebay.com/5-Digit-Num-Hand-Ta ... 43a07228f1


Not a pull chain type, but could probably be triggered then the Leaver/Arm returns to position. Or under the shell plate.
http://cgi.ebay.com/Red-Plastic-Hand-Ta ... 3caf744c77

And it's Red

Mike

[Concealed_45]

I realize this is an old thread, but just wanted to add my mod/chain replacement for future people looking.

I used a piece of 1/8" braazing rod, a grounding wire lug for the adjustable stop, and some sheet metal I cut bent welded and drilled into a sturdy extension (probably overkill)

I had everything im my garage so it was free, and took about half an hour.

[Horseman]

Very clean setup, well done....but for future people looking, this and most other "mods" replacing the chain return, while most are very well done, most if not all defeat the design purpose of the chain/spring return for the powder measure in the first place.... which is safety.....using the chain return there is no way you can double charge a case if you short stroke the press....

[Concealed_45]

This setup also accomplishes the same ass the chain setup, only more reliably. I chose it over the spring return setup for that reason. I just got this press and not used to it yet, so I wanted to keep the chance of error to a minimum.

[carload9]

if you look in your case you want overcharge or under. I got that crap out of my way.

Heres is the best loadmaster, a LLM decapping machine. Dont know who was first to think of it,, prob john lee. S Rowe helped me remember and set it up. It does all my pistol (i shoot pistol only). A gallon pretty quick plus mouth straightened out (slight pre-expansion), counted, found splits, find bad base rims, & each piece of brass has been thru loadmaster before washing and bb'ing. So they go thru LLM really smooth second time when you start to load in any machine. l like prepping brass, hav to, l pick up alot of range brass.



case feed
pre-expander
dillon counter
uni-expander
uni-decapper
down into a darwin bucket

Heres the spring set-up:



yea, this is a old thread

[Golfguy7]

Nice mod Mike -mat, I posted the same mod back in Oct 2013 still working great for me!!

[AKshooter]

I took out the large thumb screw and replaced it with a 5/16" allen head set screw. Worked great the chain does not rub anything now.

Did exactly the same thing a couple of months ago, never comes loose during operation.

[Derwoodski]

I have converted all my Pro Auto Disc powder measures to spring return... these two parts from Lee will do the trick. learned to hate the chain with the Pro1000.

Spring: AD2296
Lever: AD2309

Cost: $2:50 the shipping will be more than the parts but it all in all it's less than $7

[GhostlyOne]

I dumped the disc powder measure and went to the newer drum system. No chain "required", powder drops are accurate and consistent. Note: there is an option with this system that eliminates all chains.

Squibs: I avoid squibs and double charges by measuring ALL finished loads during the final inspection. Haven't had either since I went to the drum measure system. JMHO.

[rick25s]

"Note: there is an option with this system that eliminates all chains."

What is this option? I have that powder drum and I see no way to make it chainless.

[Gillie Dog]

"Note: there is an option with this system that eliminates all chains."

What is this option? I have that powder drum and I see no way to make it chainless.

Not real sure what your question is.

If you are referring to the Auto Drum measure, per its instructions, it may be run with chain reset of disconnect , manual finger push reset of disconnect (chainless) or removal of the disconnect all together (chainless) so it dispenses every time it is actuated (is possible to double charge)

GD

[john127]

Mike-Mat, is that a light mounted at an angle on the top outside front of the frame? If so, can you give is the specs on it and where to buy?